Go Greener Tips

Posts Tagged ‘elektronik’

Some main principles for Air Conditioner troubleshooting. For both central house Air Conditioning or window air conditioners, the essential thing to check is whether the unit is getting proper power. If the unit uses 220 volt power be sure that the appropriate voltage is coming to the unit. Same for 110 volt units. A voltage meter can be used to assure that the voltage is correct.

For window air conditioning units the voltage can also be tested before and after the thermostat. If voltage is being supplied to the thermostat but not from it then the thermostat possibly needs replaced . This is a fairly common trouble . Another place to test is the fan motor voltage. The fan on window air conditioners goes both the interior blower and the condenser fan. If that motor fails than the compressor may run for a small period of time , but will overheat and shut off. Continued operation like this will result in compressor failure. This motor can be economically replaced for bigger window air conditioners, but for smaller ones the price of replacement will be more expensive than a new unit.

Central Air Conditioners for the home are more complex and there are a great number of things that can go wrong . As with the window air conditioner the thermostat can also be a problem . The central air conditioner thermostat will only have 24 volts going to it. So don’t look for high voltage there. Some units the voltage will be getting from the outer unit and others the voltage will be supplied by the indoor air handler or furnace. The majority house central air conditioning will be supplied by the interior air handler or the furnace. If the air conditioner is for cooling only the unit will usually have only two wires going to the condenser unit. Be sure that you have 24 volts across those wires.

The next thing to pay attention to will be the interior blower. If your thermostat is used for cooling then the indoor blower should be working . If there is no air moving across the interior cooling coil then you will soon have a big block of ice formed on the coil. This can happen for a few reasons. The indoor blower is not operating , the air flow is restricted and not allowing air to move across the coil. A clogged air filter would also do this. Or the outer condenser unit has lost the charge of refrigerant.

Finally and worst of all is when you have an entire compressor damage . Usually when this occurs the compressor will “lock up” or cannot turn when power is supplied to it. Overheating or lack of lubrication are often the main reasons of compressor failure . Overheating can be caused by the outer coil around the compressor being clogged with dust , leaves, grass, or just plain old grime. The outdoor coil should be washed out each year with a good coil cleaner and water. This will assist prevent compressor failure and help maintain the unit running at peak efficacy . Changing an air conditioner compressor is a work that requires specialized equipment and needs to be done by a professional with the proper refrigeration license.

If you need further information about Electronics please contact us at www.tenar-elektronik.com

Here’s a good solution to help your family drink more water, and thus save on sodas, juices etc. It is a great thing to have a drinking water dispenser that provides you with the so needed element of life at the reach of your hand. Whether in your home or office, it is always important to drink enough on a daily basis and with a dispenser that becomes much easier and fun. Water dispensers have the possibility to change the temperature of water almost instantly. Whether you need cold or hot water, you get it as soon as you press the tab. The only proviso is that you wait a bit after refilling up the unit’s water vessel . Most models have signal lights that let you know when the dispenser is ready to be used effectively.

Water dispensers are able to heat three or five gallon bottles of water instantly. These devices are useful not only at home, but in many places where there are many people. Water dispensers vary greatly in terms of functionality they can provide. Models with just a single faucet for either cold or hot water, two faucets for both or even three faucets that include a room temperature water outlet. From simple small shapes that fit even in the narrowest of spaces, through middle range models that are great for dining halls, offices and waiting rooms, and up to full blow models to service hundreds of people a day.

There are some things you need water dispenser at your home:
- Kids love getting their own icy drink, even as young as 2 or 3 years old. They’ll line up!
- Adults tend to drink more water when they can dispense it. Sure works that way for my family; we are no different than the little ones.
- No need to ‘run’ the faucet waiting for it to get cold, it’s always icy and waiting so it can economize on your water billing.

- Great in an outside-enclosed area, like a shop or potting shed – no need to come inside for a refreshing drink.

- Some units have a hot water tap, which is just the right temperature for a quick cup of hot chocolate or tea

- Large water bottles for a dispenser are readily available and more economical than purchasing other drinks.
- You can refill your small bottles as you ‘run’ out the door.

Instead all of that’s thing, water dispensers will also help you save on electricity. Each times someone opens the refrigerator , the coldness inside is less . Other homeowners are concerned that leaving the dispenser plugged-in all day will be very costly. But newer models of these dispensers are very energy efficient. Also, you can always unplug the dispenser during the nighttime, when nobody is using it. Dispensers are also very child safe because of the safety nozzle attached to the hot water lever. This will prevent young children and careless adults from accidentally pouring hot water on themselves.

To get more information about dispenser and other electronic products, please visit out shop at www.tenar-elektronik.com

A Blender, or liquidizer in British English, is a kitchen appliance used to fusion ingredients or puree food. The term typically refers to a stationary, upright electrical device, which is to be distinguished from a hand-powered or electric mixer that may be used for alike direction . Blenders are also used in laboratory applications.

The blending container can be made of glass, plastic, stainless steel, or porcelain, and often has graduated markings for approximate measuring purposes. At the top of the container is a lid to prevent ingredients from escaping during operation. At the bottom is a blade assembly, sometimes removable for cleaning purposes. In cases where the blades are removable, the container should have an o-ring between the body of the container and the base to seal the container and prevent the contents from leaking.
Buying a blender is a seemingly simple task. However, such a huge assortment of blenders available from a multitude of manufacturers, confusion can set in quickly. There are many factors to consider such as performance, functions, capacity, colors and appearance. The blender you choose will be based on your needs, wants and taste preferences and all of these go far beyond just ice crushing ability.

The two major styles of blenders are countertop and hand held or immersion. Countertop blenders offer more power, greater jar capacity and overall versatility but they also take up more space in use and in storage. Hand held blenders are more convenient (you can blend in a pot or bowl) and take up far less space but offer much less power.
If you are planning to get one for yourself, there are some tips that maybe can help you get correct blender for you
1. Look for the best quality.

If you want to maximize the use of your blender like ice crushing or coffee grinding, look for the branded one. If you want to acquire this blender just for simple blending or mashing of fruits and vegetables or making juices and purees for your family, you can go for the cheaper Blender.

2. Look for brand new ones.

Second hand blenders may also be good but it would be better if you look for brand new appliances. Brand new ones will not only guarantee effectiveness; it will also give you assurance that the tools is in good condition. Another bad thing about second hand appliances is that they consume higher electricity than brand new ones.

3. Look for the power efficiency.

If you plan to take the blender for a simple blending function, look for a powerless blender to conserve electricity. But if the blender is for crushing ices or grinding coffee beans and nuts, pick the one with high powered motor. The higher the wattage, the greater the power.

4. Disign

Design, style and appearance including color are important factors in your decision. Blenders come in a wide various of styles such as retro, euro and contemporary. For some people performance factors outweigh appearance and others vice-versa. Personal preference will prevail for each person.
To get your favorite blender or other electronic product, please visit our Homepage at Tenar Elektronik Online Shop

A Blender, or liquidizer in British English, is a kitchen appliance used to fusion ingredients or puree food. The term typically refers to a stationary, upright electrical device, which is to be distinguished from a hand-powered or electric mixer that may be used for alike direction . Blenders are also used in laboratory applications.

The blending container can be made of glass, plastic, stainless steel, or porcelain, and often has graduated markings for approximate measuring purposes. At the top of the container is a lid to prevent ingredients from escaping during operation. At the bottom is a blade assembly, sometimes removable for cleaning purposes. In cases where the blades are removable, the container should have an o-ring between the body of the container and the base to seal the container and prevent the contents from leaking.
Buying a blender is a seemingly simple task. However, such a huge assortment of blenders available from a multitude of manufacturers, confusion can set in quickly. There are many factors to consider such as performance, functions, capacity, colors and appearance. The blender you choose will be based on your needs, wants and taste preferences and all of these go far beyond just ice crushing ability.

The two major styles of blenders are countertop and hand held or immersion. Countertop blenders offer more power, greater jar capacity and overall versatility but they also take up more space in use and in storage. Hand held blenders are more convenient (you can blend in a pot or bowl) and take up far less space but offer much less power.
If you are planning to get one for yourself, there are some tips that maybe can help you get correct blender for you
1. Look for the best quality.

If you want to maximize the use of your blender like ice crushing or coffee grinding, look for the branded one. If you want to acquire this blender just for simple blending or mashing of fruits and vegetables or making juices and purees for your family, you can go for the cheaper Blender.

2. Look for brand new ones.

Second hand blenders may also be good but it would be better if you look for brand new appliances. Brand new ones will not only guarantee effectiveness; it will also give you assurance that the tools is in good condition. Another bad thing about second hand appliances is that they consume higher electricity than brand new ones.

3. Look for the power efficiency.

If you plan to take the blender for a simple blending function, look for a powerless blender to conserve electricity. But if the blender is for crushing ices or grinding coffee beans and nuts, pick the one with high powered motor. The higher the wattage, the greater the power.

4. Disign

Design, style and appearance including color are important factors in your decision. Blenders come in a wide various of styles such as retro, euro and contemporary. For some people performance factors outweigh appearance and others vice-versa. Personal preference will prevail for each person.
To get your favorite blender or other electronic product, please visit our Homepage at Tenar Elektronik Online Shop

Air conditioners are not cheap. A bit of preventive work can make them lasting . One of the biggest problems with most air conditioning units made nowadays is that they are tough, and well built. Signs That Air conditioner Is Not Working Properly is when the air cool not flow .

The first step is to make routine inspections of your unit to discover any potential problems. There are prevention steps.

First, you must check the Filter
Dirty filters block air flow and will not let your air conditioner work correctly . Filters are important to the proper and economical operation of the air conditioning unit. They should be inspected often and changed or cleaned monthly. This is even more important during the summer months when there is a higher level of dust and pollutants in the air, and, of course, the units are running more frequently. Other methods of insuring maximum air flow through the system including cleaning and vacuuming of the registers and air vents. You should also insure that furniture and drapes are not blocking registers. Before every cooling season and once a month during the cooling season, the filter should be removed, cleaned and replaced. If you live in a particularly arid climate, this may need to be done more continuously . Most air conditioners have a washable filter that looks like a sponge.

Clean filters with a mild detergent and water, rinsing well. Let the filter dry completely before replacing. If your air conditioner comes with a fiberglass furnace style filter, do not wash it; replace it with a new filter of the same type.

Second, check the compresor
The outside compressor should be clear with a hose. Plantings should be save at least a foot away, and grass and weeds should be trimmed to insure adequate air flow around the unit. Replace any debris from the fan area. During the winter months, the compressor should be covered. It is also a good idea to remove any air conditioners during the winter, and store them until they are again needed.

Third, Check the Fan

If your fan is not working or if it is particularly noisy , it is usually caused by loose or dirty fan blades. Follow these steps to repair the fan:

1) Locate the fan inside the cabinet.
2) Use a soft cloth and/or vacuum to clean out any debris.
3) Check tightness of all blades. Vibration can loosen fan fasteners. 4) If your fan has oil ports, apply a few drops of 20-weight non-detergent motor oil.

5) If you misdoubt a faulty motor, test with the VOM on the RX1 scale. Connect VOM probes to disconnected terminal wires.
Find the latest Air Conditioner and other electronic product only at Tenar Electronic shop

Air conditioners are not cheap. A bit of preventive work can make them lasting . One of the biggest problems with most air conditioning units made nowadays is that they are tough, and well built. Signs That Air conditioner Is Not Working Properly is when the air cool not flow .

The first step is to make routine inspections of your unit to discover any potential problems. There are prevention steps.

First, you must check the Filter
Dirty filters block air flow and will not let your air conditioner work correctly . Filters are important to the proper and economical operation of the air conditioning unit. They should be inspected often and changed or cleaned monthly. This is even more important during the summer months when there is a higher level of dust and pollutants in the air, and, of course, the units are running more frequently. Other methods of insuring maximum air flow through the system including cleaning and vacuuming of the registers and air vents. You should also insure that furniture and drapes are not blocking registers. Before every cooling season and once a month during the cooling season, the filter should be removed, cleaned and replaced. If you live in a particularly arid climate, this may need to be done more continuously . Most air conditioners have a washable filter that looks like a sponge.

Clean filters with a mild detergent and water, rinsing well. Let the filter dry completely before replacing. If your air conditioner comes with a fiberglass furnace style filter, do not wash it; replace it with a new filter of the same type.

Second, check the compresor
The outside compressor should be clear with a hose. Plantings should be save at least a foot away, and grass and weeds should be trimmed to insure adequate air flow around the unit. Replace any debris from the fan area. During the winter months, the compressor should be covered. It is also a good idea to remove any air conditioners during the winter, and store them until they are again needed.

Third, Check the Fan

If your fan is not working or if it is particularly noisy , it is usually caused by loose or dirty fan blades. Follow these steps to repair the fan:

1) Locate the fan inside the cabinet.
2) Use a soft cloth and/or vacuum to clean out any debris.
3) Check tightness of all blades. Vibration can loosen fan fasteners. 4) If your fan has oil ports, apply a few drops of 20-weight non-detergent motor oil.

5) If you misdoubt a faulty motor, test with the VOM on the RX1 scale. Connect VOM probes to disconnected terminal wires.
Find the latest Air Conditioner and other electronic product only at Tenar Electronic shop

Godrej Window AC
An air conditioner is a cooling device which cools the inside of a space or entire location or office by cooling the air there. Air conditioner makes the area cool for every one there. Nothing can find you respite from the scorching summer heat than a excellent quality air conditioner. Godrej window Air Conditioning are recognized for their fine facial appearance.

Godrej is a area grown Electronics manufacturer which was before recognized for its ubiquitous steel cupboards. Later on it entered into the field of cooling devices by introducing refrigerators
which again became the pride of the apartment where they were placed. At the moment, Godrej Window air conditioners are making space in the hearts of consumers.

Window air conditioners are more in demand as compared to split ACs. They are installed on windows or any other opening. In the area, the sleek and slim façade is seen and every single one unit of AC protrudes behind it unlike split AC which has its frame placed on wall of the space and its cooling unit is placed anywhere outside the construction.

Godrej Window AC is designed with various latest facial appearance which make these air conditioners stand out of the crowd. The largely interesting part is they are designed to suit the requirements and suit the expectations of Indian consumers. Godrej window air conditioners are categorized into Navigator series and Maximizer series. Navigator series has one model of 1.5 ton. Maximizer series is comprised of two types; 1Ton and .75 ton. Godrej air conditioners, need other Godrej goods, are priced very reasonably. It creates a gentle of trust among the consumers as most of eth consumers in India are price conscious.

These air conditioners are numerous facial appearance. They include features need Blue Fin Technology, Active carbon Deodorizer, Japanese Brand Compressor, green filter, Nano meter catalyst filter and more. These ACs make air at location fresh and healthy due to the green filter. It has an eco filter and a specialized biological enzyme. It neutralizes the complete the bacteria, fungi and microbes. These air conditioners are boon for people with asthmatic problems.

Nano meter catalyst filter absorbs and deactivates the way choose unpleasant odors, virus and chemical vapors. Godrej air conditioners are equipped with Anti Rust Blue Fins technology. It keeps the aluminum fins in the temperature exchanger free from corrosion. It helps in improved efficiency, more durability and higher power savings. Other facial appearance include L Shape Cooling Coil, Sleep Kind, Gold Fin Technology, Self Diagnosis and Auto Protection Function, Backlit LCD Remote, Silent Operation and more.

Beat the summer heat with best excellence Godrej Air conditioners.

If you need further information about air conditioners and other electronics product please contact us at Tenar-elektronik

A room air conditioner is a not big , self-contained unit made to cool just one room of a house . While most models of room air conditioners are placed in windows, there are some models that are set up to come through an exterior wall opening. These small air conditioning units must be put in a window or in a wall opening, in order to allow for the air interchange that is essential for the unit to work properly .

air conditioner are often a good selection for renters, since they can be replaced fairly easily and can be put in a new location. The drawback is that these small air conditioning units tend to be quite a bit less energy effective than a central air conditioning system would be.

To encourage residential buyers to make selection that will save on electricity usage throughout the summer months, there are many utility places that have launched a “Be Cool” campaign. The purpose of this effort is to promote the benefits of purchasing room air conditioner models that are as energy efficient as possible.

In some areas , the local power companies are even embolden the residents to trade in their old air conditioners and replace these less efficient units with good room air conditioners.

Recently , one more advantage to using energy effective air conditioning systems is a federal tax credit. Individuals who choose to install any type of air conditioning units will be eligible for a federal tax credit of as much as $300.

The air conditioning parts that qualify for this tax credit are quite costlier to buy than the ordinary air conditioners that use more energy to work . However , calculating the tax incentive, along with the lessening in the cost to run the unit, clearly shows that it is well worth it to install new units that qualify.

In most examples , the sum will more than offset the initial, higher cost of energy efficient, air conditioning units.

When choosing a room air conditioning unit, professionals recommend that it is best to purchase the best model that is affordable , but not necessarily the biggest unit. The unit should suit the amount of space available , while taking into consideration the room size.

Buying a room air conditioner model that is bigger than what is needed actually means that it will be using more energy and will not be efficient at all. This wasted energy is because of the cycling of the motor that operates to hold the room at the right temperature.

If you need further information about electronics please contact us at www.tenar-elektronik.com

A room Air conditioner is a not large enclosed cooling device that is can be put in a window or through a wall for venting and for air exchange . Lately , there has also been an introduction of portable air conditioning units, which are housed in cases that sit on the floor near a window with a tube for venting. These portable units as a rule have casters mounted to the bottom of the case making it possible for them to easily remove from one room to another as needed.

The aim of air conditioning equipment for a room is to cool the air within a small, limited area and they are not intended to be used as a “whole house” air conditioning system. They are most common placed in houses where people are renters; therefore , they are not permanently set up and can be removed and taken to a new location if the occupant moves .

Usually , a room air conditioner will have a control panel mounted somewhere on the front or on top, in order to give the user quite easy access to the controls. In general , there are independent controls for regulating the target room temperature and for controlling the fan speed for circulating the conditioned air around the room .

Most people are not aware that room air conditioning units do not “technically” cool a room. It is more correct to say that room air conditioners remove the heat from the air and then moves it elsewhere to the place where the unit has been vented.

A pressurized refrigerant, R-22, flows through the air conditioner unit when it is turned on. While the unit is on, the condenser will pluck the refrigerant gas into the air conditioning system and then pressurize it, which makes the temperature higher . This heated, high-pressure gas moves next to the condenser coils, which are situated on the outdoor portion of the unit where the fans distribute the heat that has gathered .

The cooled gas then becomes condensed into a liquid, which moves to the inner of the room air conditioner to the evaporator coils. The fan then moves the air throughout the unit. The thermostat direct the cycling of this process to support the desired temperature in the room.

Certain room air conditioners have mechanical controls, such as knobs and push buttons. The newer air conditioning units are controlled with Electronics touch-pads that tend to give more functionality and are able to regulate the mode the units operate in, the temperature set point, a timer for automatic shut off and powering on, and different other conveniences, most of which are designed to make the unit as energy efficient as possible.

if you need further information please contact us at Tenarelektronik

A room Air conditioner is a not large enclosed cooling device that is can be put in a window or through a wall for venting and for air exchange . Lately , there has also been an introduction of portable air conditioning units, which are housed in cases that sit on the floor near a window with a tube for venting. These portable units as a rule have casters mounted to the bottom of the case making it possible for them to easily remove from one room to another as needed.

The aim of air conditioning equipment for a room is to cool the air within a small, limited area and they are not intended to be used as a “whole house” air conditioning system. They are most common placed in houses where people are renters; therefore , they are not permanently set up and can be removed and taken to a new location if the occupant moves .

Usually , a room air conditioner will have a control panel mounted somewhere on the front or on top, in order to give the user quite easy access to the controls. In general , there are independent controls for regulating the target room temperature and for controlling the fan speed for circulating the conditioned air around the room .

Most people are not aware that room air conditioning units do not “technically” cool a room. It is more correct to say that room air conditioners remove the heat from the air and then moves it elsewhere to the place where the unit has been vented.

A pressurized refrigerant, R-22, flows through the air conditioner unit when it is turned on. While the unit is on, the condenser will pluck the refrigerant gas into the air conditioning system and then pressurize it, which makes the temperature higher . This heated, high-pressure gas moves next to the condenser coils, which are situated on the outdoor portion of the unit where the fans distribute the heat that has gathered .

The cooled gas then becomes condensed into a liquid, which moves to the inner of the room air conditioner to the evaporator coils. The fan then moves the air throughout the unit. The thermostat direct the cycling of this process to support the desired temperature in the room.

Certain room air conditioners have mechanical controls, such as knobs and push buttons. The newer air conditioning units are controlled with Electronics touch-pads that tend to give more functionality and are able to regulate the mode the units operate in, the temperature set point, a timer for automatic shut off and powering on, and different other conveniences, most of which are designed to make the unit as energy efficient as possible.

if you need further information please contact us at Tenarelektronik